Back to Blog

Dead Pixel and Stick Drift Tests Before You Buy Used

Utility

Checks to run on a used controller, keyboard, laptop screen, mic and webcam before you pay, what each result means, and when to walk away or bargain.

Faults in used electronics are rarely hidden on purpose. A seller may simply never have noticed a stuck pixel in the corner or a stick that creeps when nobody touches it. You will notice within a week. Ten minutes of testing at the handover turns that week into a conversation about price, or a reason to keep your money.

All you need is a laptop with an internet connection, and for a controller, a cable to plug it in. Everything below runs from a web page, so nobody has to install anything.

A controller: buttons, triggers and stick drift

Open the gamepad tester, connect the controller and press any button so it shows up. Then work through it in this order.

  1. Press every button once. Each one is marked on the diagram as it registers, and the results list counts how many are done and names any that have not been pressed. A button that never gets marked is a dead button.
  2. Pull each trigger all the way and let go. The result should read full travel and back to zero. A trigger that never reaches the top, or rests above zero after you let go, is worn or sticking.
  3. Rotate each stick slowly around its edge two or three times. The tester draws the outline the stick reaches. A shape that falls short on one side means the stick cannot reach full travel in that direction.
  4. Run the drift check and do not touch the controller. For a few seconds it records where each stick rests.

The drift result is the one that matters most, and it comes in three bands. Under 5% off center is normal. Between 5% and 10% is noticeable; a slightly larger deadzone hides it, in games that let you set one. Over 10% is drift: games will read movement you are not making, and it usually gets worse, not better.

If the tester says vibration is not reported, that is not a fault: some controller and device combinations simply do not pass that information on. Test rumble on the console itself if it matters to you.

Verdict: every button marked, triggers full travel, drift normal or noticeable, and the controller is fine. Drift over 10% means you are buying a controller that needs a repair, and the price should say so.

A keyboard: dead keys and double typing

In the keyboard tester, click the keyboard picture and press every key. Each key is marked as it registers; turn on the numeric keypad view if the board has one. Press Esc three times quickly when you want to leave the test area.

Two problems show up here that a quick typing test in a text box misses. A key that never lights up is dead. A key marked as registered twice fired again a moment after you released it. That is the beginning of double typing, the fault that puts two letters in a word when you pressed one, and it rarely fixes itself.

The results also show the most keys registered at once. For gaming, hold the keys you would really hold together, for example W, A, Shift and Space, and see that all of them register. Do not judge an office keyboard harshly for a low number here: many are built to handle only a few keys at once, and that is a design limit, not a fault.

A laptop or monitor screen: the dead pixel test

Set the page zoom to 100%, open White Screen and start the dead pixel test. It fills the screen with black, white, red, green, blue, cyan, magenta, yellow and mid gray, one at a time, and you tap or press Space to move on.

  • A dot that stays lit on the black screen is a stuck pixel.
  • A dot that stays dark on the white screen is a dead pixel.
  • A dot that is wrong on only one color is a stuck subpixel, and it is easiest to spot on red, green or blue.

On the black screen, also look at the edges and corners in a dim room. Patches of light leaking in there are backlight bleed. Some is normal on many LCD panels; bright patches you can see with the lights on are not.

The same page lists the screen size in device pixels. If the listing said 1920 x 1080 or 2560 x 1600, that is the number you should see with zoom at 100%. A smaller number than advertised is worth asking about.

Verdict: one stuck pixel near an edge is a reason to bargain. A dead or stuck pixel near the middle of the screen is a reason to walk away, because you will look straight at it every day.

Microphone and webcam

On a laptop, run the mic test and then record 5 seconds and play it back. The level meter says whether sound arrives at all; the playback tells you what it sounds like. The verdict tells you plainly if the signal is silent, very quiet or clipping. Silent on a laptop that should have a built-in microphone is a hardware or settings problem you want explained before paying.

Then start the webcam test. If the camera opens but sends only black, look for a privacy shutter over the lens before assuming it is broken. If a listing promised a 1080p camera, choose Full HD in the resolution list and check what the page reports back. A low frame rate in a bright room is a weak camera; in a dark room it is normal.

What to do with the results

Write down what you found and show it on the screen: "two keys register twice, the left stick rests at 12% off center". A specific, visible fault is much easier to negotiate on than a feeling. Then decide by what the fault costs you:

  • Walk away: drift over 10%, a dead pixel near the center of the screen, dead keys you use every day, a microphone or camera that does nothing on a laptop you will use for calls.
  • Bargain: noticeable drift that a deadzone hides, a stuck pixel at an edge, mild backlight bleed, a key you never use.
  • Pay the asking price: every key and button working, drift normal, no marks on any of the test colors.

Do the same checks again on the first day you own it, while a return is still possible. Some faults only appear once the device is warm.